ReaSnow Forum
Products => ReaSnow S1 => Topic started by: V1RUS3647 on February 15, 2022, 10:07:05 PM
-
in warface on xbox compared to ps4 mouse sensitivity is ~2 times faster and there is a shaking of the sight, this problem occurs for all users of reasnow s1 on xbox
-
We will need the following details to help you:
1. your console and game
2. mouse DPI/CPI and USB report rate, mouse model, and producer
3. settings in the game on console, such as sensitivity, dead zone, acceleration, aim assist, etc.
it's better to restore all settings in game and change the settings as shown in our APP, and try it again with a default game config.
4. which config has been activated in ReaSnow S1?
your settings for HIP/ADS /HIP YX Ratio/HIP MIN/ADS YX Ratio/ADS MIN/curve in this config
5. ReaSnow S1 firmware and APP version
6. a video to show us your trouble will be better.
-
1. xbox one / warface
2.6000 dpi, 1000 report rate, logitech g102
3.in-game settings: in basic control sensitivity 14/14, in advanced control: ADS close/mid/high-range 120%, inner deadzone 8%, outer deadzone 2%, yaw speed 50, pitch speed 50, yaw acceleration 0, pitch acceleration 0, acceleration time 0, acceleration delay 0, stick response curve 20, in ADS the settings are the same.
4. config warface in reasnow: delay 0, sensitivity 0.90, and in ADS, deadzone 16, YX ratio 1.5, MIN speed 0, smoothness 0, curve default.
5. 5. APP version 1.4.3 / firmware 5.4.22
6. I also sent videos and photos to the mail support@reasnow.com
-
1. restore all settings in warface
2. then change them as shown below:
(Basic Controls)
Sensitivity = 14
ADS Sensitivity = 14
(Advanced Controls)
ADS Close-range = 100%
ADS Mid-range = 100%
ADS High-range = 100%
Inner Deadzone = 12%
Outer Deadzone = 10%
Advanced Control Options = Disabled
BY THE WAY, we did not get your email.
when did you send it?
-
on ps4 my settings work perfectly, but on xbox the sensitivity is 2-3 times faster and there is a shaking of the sight, is it possible to fix the config on xbox that the management was identical?
-
have you followed my recommendations above?
-
yes, the sight stopped shaking, but the mouse stopped moving linearly, the mouse began to move then quickly, then slowly, with such settings it is very difficult to play, can you fix the config so that the sensitivity is identical to ps4 and I can play on my settings?
-
but you can lower the HIP and ADS sensitivities with our APP,
to compensate for the difference:)
it will be the easiest solution.
-
I have already tried on different dpi, on different sensitivities both in the game and in reasnow, but on xbox it does not help, is it possible to edit the config on xbox and if not, then why can't it be done? in other games I did not notice this and play on the default settings and everything is perfect, here the problem is specifically in the config warface xbox, or in the console itself.
-
of course, we can change our config for Xbox.
but can you elaborate on " have already tried on different dpi, on different sensitivities both in the game and in reasnow, but on xbox it does not help"?
we changed HIP and ADS sensitivities here in warface config with our APP,
and we can have any sensitivity we need.
-
I can reduce the sensitivity, but the sight will also shake, so I change the curve in the game, which removes the shaking of the sight but the acceleration of the mouse appears, and its behavior changes slightly which is not very convenient. please change the config if possible
-
hi richard, i confirm what virus wrote, the sensitivity between ps4 and xbox is different, our sensitivity is x2 / 3 times faster and if we reduce the deadzone to get more acceleration the aim trembles. also I tried the new aim assist beta on xbox (warface) it does not work there is a need to add a macro that makes the character move left and right, but on ps4 it works correctly without having to add anything.
-
Try to turn up the values
-
I play for 2 years on reasnow i try many settings...
Now i play with warzone config on warface and i dont have problems.
-
That's good. For me the Warface config is the best. Everything works fine for me but we all have different taste when it comes to our gameplay.
-
@Ezot @V1RUS3647
1. add a new warface config in ReaSnow S1.
2. restore all settings in your warface on XBox or PS, and change the recommended settings as shown in the popped-up window while adding this new warface config.
-
I wrote that this does not solve the problem, but only makes it worse.
-
as stated previously,
the recommended settings for deadzones are:
Inner Deadzone = 12%
Outer Deadzone = 10%
please change them properly and try it again.
-
https://youtu.be/OdKE4YgUXh4 hi guys this guy has good settings. If it's too slow, turn your reasnow s1 manager sensitivity up.
-
it doesn't help or fix the situation. why can't you just reduce the sensitivity in the config by 2 times and fix the dead zone so that the emulation is like on ps4 and I can play on the same settings as on ps4.
-
https://youtu.be/OdKE4YgUXh4 hi guys this guy has good settings. If it's too slow, turn your reasnow s1 manager sensitivity up.
if the xbox had identical emulation, I'd love to play on these settings.
-
I don't know bro. I'm not exactly a professional but maybe you can try to get similar sensitivity and get used to that so it's almost the same as the old ones :)
-
because no other users have the same issue as you did,
if we change the default config, it might bring trouble to many no-issue users.
we do think your issue is just the sensitivity,
if so, you can simply reduce the sensitivities in our APP or reduce your mouse DPI,
then all will be solved.
-
check the emulation on xbox and ps4... see for yourself that emulation needs to be fixed on xbox
-
we check our config for warface on Xbox again,
but there is no shaking at all.
can you send a video to show us the following details?
1. all the in-game settings in warface as recommended in our APP
2. you have added a new and default config for warface
3. the shaking of the cursor while moving your mouse